Request A Call Back

    Category: Barrel Saunas

    Ukko Cedar Barrel Sauna
    Ukko Cedar 2.4m long at 1.8m dia barrel sauna is going to Gold Coast, QLD
    It is Saturday but we had to work and finish test fit of our popular Canadian Western Red Cedar barrel sauna. Maxim, our customer, is coming over tomorrow to pick it up and we had to make sure that it’s all fitted properly :).
    Ukko Barrel sauna assembly
    Sauna is half way done. Base staves are in. Front and back walls are in too..
    Ukko Barrel sauna assembly
    The same half way through sauna but from another angle..
    Customer ordered traditional sauna door. The reason is that his house does not have enough power for 8kW electric sauna heater and maximum he can go for is only 6.0Kw.
    Traditional timber door holds heat much better (a bit of cost but way less than upgrading house power supply).
    Ukko traditional sauna door
    Traditional sauna door is mounted to the door jamb..
    As always, all our saunas are fitted with two benches along sauna walls:
    Ukko barrel sauna top view
    Sauna benches are fitted along with floor duck board and heater guard rail..
    Still few staves to go and maybe no need for filler stave:
    Ukko Barrel sauna assembly
    Ooh.. just a bit more to go..
    Well, filler stave it is and sauna is done:
    Ukko barrel sauna
    Sauna is finally done and dusted. Ready to be picked up and go to its new home..

    We always get questions like how much..

    Here it is with traditional door 1.8m dia at 2.4m length, electric heater with built-in controls, heater guard rail, two benches, floor duck board, air vents, sauna light fitting, sauna cradle, bucket, ladle and thermometer – $12,490.

    Want to order yours? Call us on:

    0425 230 785

    Ukko barrel sauna
    2.7m long Ukko Cedar barrel sauna with overhang, curved traditional door with round window and front seat to relax after sauna session
    We are packing this custom made sauna for a client in Brisbane. It features 600mm overhang, front seat, and big window at the back for relaxing views:
    Barrel sauna back wall
    Window at the back sauna wall for scenic views
    This is how this barrel sauna looks from inside:
    Barrel sauna inside
    Two benches along each sauna sides with Cedar head rests
    Sauna front with towel
    Look, we’ve hang the towel to make it look more inviting 🙂
    Oh, and it will be supplied with electric heater and bitumen shingles to protect it from the rain
    Want to order your sauna today? Call us on 0425 230 785 for more information.
    Save Save Save Save Save

    Ukko barrl sauna
    1.8m dia at 1.8m length Ukko Cedar barrel sauna
    We just finished refurbishing our 1.8m long Cedar barrel sauna. This sauna was used by us in Sydney before moving to Sussex Inlet. In case you are wondering how we deliver it – simple, we flat pack it on to a made pallet for courier pickup this week:
    Flat packed sauna on a pallet.
    All of the barrel sauna is inside this cute box 🙂
    While we were test fitting this sauna for customer in Torquay, VIC, we decided to show you how to assemble front and back wall of our barrels.

    FRONT WALL ASSEMBLY:

    Barrel front wall assembly
    Lay all 3 wall parts and connect them together to make a perfect circle
    Once all wall parts are together, simply screw them with supplied hex screws.

    BACK WALL ASSEMBLY:

    It is very similar to front wall except that there’s one more extra detail.
    Step 1 - back wall assembly
    Step 1- Lay barrel sauna back wall parts
    Step 2 - back wall assembly
    Step 2 – Connect all parts together. (You can use rubber mallet)
    Step3 - back wall assembly
    Step 3 – Screw all parts together with supplied hex screws
    Note: In this image all parts are separate. This is just to show you where the parts need to be screwed together. Make sure that all wall components are tight together (the same as front wall)
    Step 4 - back wall assembly
    Step 4 – Attach back wall support panel where marked and screw it down to the back wall
    That’s all there’s to it. Any questions, please contact us for more information. Save Save Save Save Save Save Save

    Barrel Sauna Assembly

    We’ve just finished test fit of our 2.1m long Cedar barrel sauna. While we were test fitting this sauna, we thought to make few pictures and show you how you can assemble it yourself.
    Ukko Barrel Sauna
    2.1m long at 1.82m diameter Ukko Cedar Barrel sauna
    This sauna features traditional sauna door with square window, bitumen shingles for outdoor installation (if there’s no pergola to cover the sauna) and sauna air humidifier with Eucalyptus oil. We did not put rings (you can see them near the shingles) but they need to be installed and tightened when putting this sauna on site.

    Here’s how to assemble Ukko Cedar barrel sauna:

    Step 1

    Place sauna base staves on to the supplied cradle. Fix one stave only at this stage to the cradle with supplied hex screws (we pre-drill holes. You can’t miss it):
    Sauna Cradle
    Barrel Sauna Cradle
     
    Barrel Sauna base staves
    Place base staves (marked from B1…) on to the cradle and screw one stave down

    Step 2

    Place front and back walls in to the staves grooves:
    Sauna front and back walls
    Placing sauna front and back walls on to the base staves
    Use level to ensure front and back walls are properly leveled:
    Leveling front wall
    Leveling front wall

    Step 3

    Continue with staves until sauna is fully done:
    Continue placing staves 1
    Go one half of the barrel on one side first
     
    Continue placing staves 2
    Then go to the other half of the sauna
    Screw every second stave on to the walls to fix them during installation. (Before placing rings, you remove screws):
    Continue with placing staves 3
    Putting screws in to the staves to secure them until rings are in place
     
    Staves are in place
    All staves are in place (use rubber mallet to ensure tight fit)

    Step 4

    Place stainless steel rings and tighten them with supplied rods and couplings:
    Placing barrel sauna rings
    Use ring protective strip (or tape measure) to get 50mm from the edge of the staves on both sides

    Step 5

    Mount sauna door to the door jamb:
    Traditional sauna door
    Screw sauna door hinges to the door jamb

    Step 6

    Install bench supports and place benches on top of them (you can choose the best possible height for you). We normally put one bench lower for sitting and one upper for laying down (it will be hotter there). Mount sauna heater with guard rail, put sauna light fitting (under one of the benches) and place floor duckboard:
    Installing sauna benches
    Installing sauna benches
    Well, that’s pretty much it. All you need now is a licensed electrician to hook the heater to your mains and connect sauna light fitting with an on/off switch (on/off switch must be somewhere outside of the sauna). Once all is connected you can start enjoying your sauna.
    If you have more questions or would like to place an order simply CONTACT US via email “sales(at)ukkosaunas.com.au” or via phone:

    0425 230 785